Jump to content

  • Quick Navigation
Photo

Help please! Cheese Packing Question

Share this

  • You cannot start a new topic
  • Please log in to reply
8 replies to this topic
- - - - -

Quality cheese

    Grade - Active

  • IFSQN Active
  • 7 posts
  • 0 thanks
0
Neutral

  • Scotland
    Scotland

Posted 14 January 2010 - 11:02 PM

Hi All,
I'm looking for any information on the obsorbance of CO2 in cheddar cheeses. We flush all pre-pack cheese with 100% CO2 and seem to be getting issues with some packs not snugging/bedding down. Upon inspecting these packs, there seems to be no evidence of failed seals using -750mb vacuum tanks. However when testing the residual oxygen, we still seem to find elevated levels of O2 still present in the packs.
Has anyone else has issues similar to this?
Is there any possibility of the CO2 being obsorbed into the product leaving only O2? Surely this would not increase the O2 level, we have online analysers that alarm and stop if the target goes over our limit of <1%?



Simon

    IFSQN...it's My Life

  • IFSQN Admin
  • 12,826 posts
  • 1363 thanks
880
Excellent

  • United Kingdom
    United Kingdom
  • Gender:Male
  • Location:Manchester
  • Interests:Married to Michelle, Father of three boys (Oliver, Jacob and Louis). I enjoy cycling, walking and travelling, watching sport, especially football and Manchester United. Oh and I love food and beer and wine.

Posted 15 January 2010 - 08:23 AM

BUMP for Quality Cheese.


Get FREE bitesize education with IFSQN webinar recordings.
 
Download this handy excel for desktop access to over 180 Food Safety Friday's webinar recordings.
https://www.ifsqn.com/fsf/Free%20Food%20Safety%20Videos.xlsx

 
Check out IFSQN’s extensive library of FREE food safety videos
https://www.ifsqn.com/food_safety_videos.html


Madam A. D-tor

    Grade - PIFSQN

  • IFSQN Principal
  • 644 posts
  • 230 thanks
52
Excellent

  • Netherlands
    Netherlands
  • Gender:Female
  • Interests:meat, meat products, ready to eat, food safety, QMS, audits, hazard analyses, IFS, BRC, SQF, HACCP, ISO 9001, ISO 22000

Posted 15 January 2010 - 09:28 AM

Some brainstorming:
Is it possible that there are micro leakages in your foil?

Did you change to a new foil supplier?

Has the equipment changed? Is is properly working (how do you check correct working of flushing)?

After what time do you find the levels of O2? In production or after shelf life?

How about microoranisms?


Kind Regards,

Madam A. D-tor

cazyncymru

    Grade - FIFSQN

  • Banned
  • 1,604 posts
  • 341 thanks
130
Excellent

  • Earth
    Earth
  • Gender:Male

Posted 15 January 2010 - 09:51 AM

I must admit that in the past i've used nitrogen for gas flushing cheese bags and had no issues.

Caz



Snitzel

    Grade - AIFSQN

  • IFSQN Associate
  • 30 posts
  • 1 thanks
0
Neutral

  • Earth
    Earth
  • Gender:Male

Posted 15 January 2010 - 10:27 AM

Has the equipment changed? Is is properly working (how do you check correct working of flushing)?


Check not just for the flushing equipment but also for the gas measuring devices....

As far as microorganisms are concerned I cant think of any microorganisms in food that will produce oxygen, the typical is to get CO2 or SO2...

Did you check that your CO2 supply is 100% CO2?

Also I have seen that sometimes when the gas mixture (CO2 and/or nitrogen) tank is almost empty you might get a number of paks that contain high levels of oxygen


Quality cheese

    Grade - Active

  • IFSQN Active
  • 7 posts
  • 0 thanks
0
Neutral

  • Scotland
    Scotland

Posted 15 January 2010 - 11:17 PM

Thanks for the replies guys... we have online gas analysers that are designed to stop production if the gas flush exceeds the target of <1% O2, we also check the flush with handheld units that show the levels of CO2 & O2.
Some of the retained samples that do not bed down are tested within 5 days using the vacuum tank (-700mb), with no leakers evident and higher levels of O2 when tested using the handheld analysers.
My thinking is that the leaks may be so slight that the CO2 sensor may not be detection the leaking gas?



Hongyun

    Finger Lickin' Good

  • IFSQN Member
  • 241 posts
  • 20 thanks
3
Neutral

  • Singapore
    Singapore
  • Gender:Male
  • Location:Singapore

Posted 18 January 2010 - 04:38 AM

Could it be the material of your packaging? All kinds of polymer are porous to some extend and O2, CO2 and moisture can enter and leave the pack, depending on the surrounding conditions.

Surrounding air has less than 1% CO2. Thus, if your pack contains 100% CO2, and the polymer of your pack has a poor barrier, then CO2 will exit from the pack to the environment at a rather fast pace to reach equilibrium.

If this theory is sound, then maybe you should get your packaging materials checked out. Perhaps do a COTR to confirm.

If changing another polymer is too expensive, then maybe you can change to N2 instead of CO2. Surrounding air has 78% N2, should take a longer peroid of time for them to escape out of the packaging.



&quot;World Community Grid made it possible for us to analyze in one day the number of specimens that would take approximately 130 years to complete using a traditional computer.&quot;

- Dr. David J. Foran, professor and lead researcher at The Cancer Institute of New Jersey, UMDNJ-Robert Wood Johnson Medical School.




Join our LinkedIn Group! &gt;&gt; &lt;&lt;

Charles.C

    Grade - FIFSQN

  • IFSQN Moderator
  • 20,542 posts
  • 5662 thanks
1,544
Excellent

  • Earth
    Earth
  • Gender:Male
  • Interests:SF
    TV
    Movies

Posted 18 January 2010 - 06:26 AM

Dear QC,

No idea regarding the practical measurement limitations but as implied in the previous posts, looks like a plot of Conc.(O2) vs time is required for some random samples.

Its called "validation" :smile:

Rgds / Charles.C


Kind Regards,

 

Charles.C


Tony-C

    Grade - FIFSQN

  • IFSQN Fellow
  • 4,223 posts
  • 1288 thanks
608
Excellent

  • United Kingdom
    United Kingdom
  • Gender:Male
  • Location:World
  • Interests:My main interests are sports particularly football, pool, scuba diving, skiing and ten pin bowling.

Posted 25 January 2010 - 01:53 AM

I must admit that in the past i've used nitrogen for gas flushing cheese bags and had no issues.

Caz


Agreed I would be flushing with Nitrogen.

Regards,

Tony




Share this

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users