Jump to content

  • Quick Navigation
Photo

Pallet Wrapping

Share this

  • You cannot start a new topic
  • Please log in to reply
7 replies to this topic

brianweber

    Brian

  • IFSQN Senior
  • 293 posts
  • 114 thanks
31
Excellent

  • United States
    United States
  • Gender:Male
  • Location:Fond Du Lac, Wisconsin
  • Interests:Cheese, Coffee, Golf, Scrabble, Food Safety, HACCP, BBQing

Posted 01 September 2015 - 03:39 PM

Looking for some clarification. We produce composite paperboard cans. We stack these on a palet, place slip sheets in between each layer then wrap with plastic on our palletizer. Do I need to maintain lot numbers/ traceability on the slip sheets and the wrapping material? The slip sheets, for those unfamiliar with them, are thin cardboard sheets that separate layers on the palet.  Any insight would be greatly appreciated!


Brian


Setanta

    Grade - FIFSQN

  • IFSQN Fellow
  • 1,610 posts
  • 371 thanks
389
Excellent

  • United States
    United States
  • Gender:Female
  • Interests:Reading: historical fiction, fantasy, Sci-Fi
    Movies
    Gardening
    Birding

Posted 01 September 2015 - 03:56 PM

It is not something we've done.  We wrap pallets and use slip sheets and sometimes old master cases AS slip sheets.  We haven't been dinged for that....yet. :blink:


-Setanta         

 

 

 


Thanked by 1 Member:

brianweber

    Brian

  • IFSQN Senior
  • 293 posts
  • 114 thanks
31
Excellent

  • United States
    United States
  • Gender:Male
  • Location:Fond Du Lac, Wisconsin
  • Interests:Cheese, Coffee, Golf, Scrabble, Food Safety, HACCP, BBQing

Posted 01 September 2015 - 04:01 PM

I can argue both sides of it. I would certainly like to NOT have to do it! Thank you Setanta!

 

Brian


Setanta

    Grade - FIFSQN

  • IFSQN Fellow
  • 1,610 posts
  • 371 thanks
389
Excellent

  • United States
    United States
  • Gender:Female
  • Interests:Reading: historical fiction, fantasy, Sci-Fi
    Movies
    Gardening
    Birding

Posted 01 September 2015 - 04:07 PM

You're welcome! I have an SQF Level II later this month, I'll let you know if it comes up!


-Setanta         

 

 

 


brianweber

    Brian

  • IFSQN Senior
  • 293 posts
  • 114 thanks
31
Excellent

  • United States
    United States
  • Gender:Male
  • Location:Fond Du Lac, Wisconsin
  • Interests:Cheese, Coffee, Golf, Scrabble, Food Safety, HACCP, BBQing

Posted 01 September 2015 - 04:12 PM

Awesome, please do. Good luck on your audit!


Brian


Thanked by 1 Member:

CMHeywood

    Grade - SIFSQN

  • IFSQN Senior
  • 457 posts
  • 119 thanks
42
Excellent

  • United States
    United States
  • Gender:Male
  • Location:Neenah, Wisconsin

Posted 02 September 2015 - 07:44 PM

If your slip sheets or stretch wrap were a source of contamination which lead to an FDA recall, then you would likely be asked for traceability information.



SQFconsultant

    SQFconsultant

  • IFSQN Fellow
  • 4,662 posts
  • 1139 thanks
1,132
Excellent

  • United States
    United States
  • Gender:Male
  • Interests:Just when I thought I was out - They pulled me back in!!!

Posted 04 September 2015 - 02:48 AM

Yes, you need to track your packaging and additional items like slips and wrapping.  As far as the comment on the SQF, same applies.   


All the Best,

 

All Rights Reserved,

Without Prejudice,

Glenn Oster.

Glenn Oster Consulting, LLC -

SQF System Development | Internal Auditor Training | eConsultant

Martha's Vineyard Island, MA - Restored Republic

http://www.GCEMVI.XYZ

http://www.GlennOster.com

 


Thanked by 1 Member:

CMHeywood

    Grade - SIFSQN

  • IFSQN Senior
  • 457 posts
  • 119 thanks
42
Excellent

  • United States
    United States
  • Gender:Male
  • Location:Neenah, Wisconsin

Posted 04 September 2015 - 03:20 PM

I work at a packaging converter that uses LDPE resin.  Since we use a large amount of it, we store it in a 30 foot tall silo.  Different shipments of LDPE will be dumped on top of the previous shipment.

 

This means we have to consider a wider window for what was actually used on that day.  For example:  based on usage, we thought we were close to using Shipment B versus Shipment A but didn't know for sure.  The resin empties in a cone shape.  Thus we would need to trace back Shipment A and Shipment B, and trace forward to which products used either shipment of LPDE in a window of several days before and after the production lot in question.

 

So the issue is not whether we ignore traceability because it is a daunting task for some items but rather can we set up a system and establish the resources to handle a large scale investigation.





Share this


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users