Jump to content

  • Quick Navigation
Photo

Sanitary Knife Storage and Use

Share this

  • You cannot start a new topic
  • Please log in to reply
3 replies to this topic

Guitardr85

    Grade - AIFSQN

  • IFSQN Associate
  • 49 posts
  • 4 thanks
3
Neutral

  • United States
    United States
  • Gender:Male
  • Location:Chicago, IL
  • Interests:HACCP, HARPC, SQF Practitioner, FSMA, Food Safety Culture, Reading, Creative Writing, Guitars, Piano, Music, Art, Wanderlust, Traveling.

Posted 12 January 2017 - 08:29 PM

Happy Thursday everyone!

 

I am hitting a bit of a self-implicating road block in terms of sanitary knife storage and use.  I am looking for a best practice for the daily use, storage, and sanitation of knives used for both opening non-food contact packaging bundles (e.g. outer containers of deli lids, etc.) and food contact bulk material knives.  

 

What is giving me a headache is one particularly large production room that shares 6 different production lines.  Even with numbering the knives by line, I am still at the impasse of how to ensure that knives are returned to storage when not in use and...how to keep the holders clean in the first place as our knives are segregated by color for both non-food and food contact use.  Other than ordering 20 to 30 separate knife holder stations for ease and accessibility for all employees on the line are there any central storage and usage options that don't present a "non-stored" knife issue if an employee needs to keep a knife on a food contact table for the shift?

 

This is likely a simple matter that is just generating a risk feedback loop in my head, but any advise or suggestions would be very much appreciated.

 

Thanks Everyone!



FurFarmandFork

    Food Safety Consultant, Production Supervisor

  • IFSQN Fellow
  • 1,264 posts
  • 590 thanks
206
Excellent

  • United States
    United States
  • Gender:Male
  • Location:Oregon, USA

Posted 13 January 2017 - 03:28 PM

I run into these loops also, sometimes you want to increase control because it's a good idea, but then get punished for it on your audit because you couldn't implement it perfectly! I'm having the same conversations right not about adding production smocks where there were none before in my facility.

 

Before you move forward with a final decision, I would encourage you to do these two things first.

 

1. The 6 lines, is there a risk of cross contamination from tools for allergens, lots, etc? A risk analysis for this project should start here, so that you can ultimately defend whatever practice you decide is best. Sounds like you have this covered by numbering them by line, so good work, but I bet getting employees to comply might be tough.

 

2. Segregate your hazards/goals into three categories, personnel safety, food safety, and production efficiency. Determine your order of options and preferences in that priority order.

 

This information will let myself and others on the forum help give you a more specific answer. I'll try to give my opinion based on the information in your post regardless.

how to keep the holders clean in the first place as our knives are segregated by color for both non-food and food contact use

 

 

First thing, your product contact and non-product contact knives probably shouldn't have the same or interchangeable holders. With regard to keeping them clean, I can't weigh in on that without knowing if this is a knife block or what. If it's a toolbox or knife block, my response would be simple and that they should get cleaned at whatever interval other DPC surfaces and the knives get cleaned if you're going to use them even with in-use utensils. If don't want to clean the container as often, then knives should only be returned to the holder clean, and should remain on the line if dirty, to be cleaned before returning.

Other than ordering 20 to 30 separate knife holder stations for ease and accessibility for all employees on the line are there any central storage and usage options that don't present a "non-stored" knife issue if an employee needs to keep a knife on a food contact table for the shift?

 

So a "non-stored" issue is confusing to me. If your production room is active for the shift, there's no food safety reason it couldn't sit on the table like any other DPC surface. In terms of personnel safety, I can understand wanting blades to be put away or sheathed.

 

Off the top of my head if I was proposing a program for this room, what I might do is have a central location where employees can retrieve clean knives, the location always stays clean and only contains cleaned knives returned from where you do sanitation (nothing goes into the station unless coming in clean). Then for safety/convenience, at each work station, you could install a magnetic block (http://image.made-in...-Knife-Rack.jpg) that's easily cleanable for in-use knives to be stored at the work station. At the end of shift, all dirty knives go to sanitation, get cleaned, and are returned to the central location/stock.

 

Alternatively, if your lines aren't actually cutting/chopping products and you're just opening bags of ingredients, you could ditch this program entirely and use single-use disposable knives (https://www.google.c...0k1.7GuA0ts_AYA). Selecting colors for dedicated lines or tasks. Do an ROI and see if it's ultimately cheaper to manage.


Austin Bouck
Owner/Consultant at Fur, Farm, and Fork.
Consulting for companies needing effective, lean food safety systems and solutions.

Subscribe to the blog at furfarmandfork.com for food safety research, insights, and analysis.

Thanked by 1 Member:

Charles.C

    Grade - FIFSQN

  • IFSQN Moderator
  • 20,542 posts
  • 5662 thanks
1,544
Excellent

  • Earth
    Earth
  • Gender:Male
  • Interests:SF
    TV
    Movies

Posted 13 January 2017 - 03:36 PM

Hi guitar,

 

You may find this slightly different parallel thread of some interest -

 

http://www.ifsqn.com...n-conformances/


Kind Regards,

 

Charles.C


Thanked by 1 Member:

Guitardr85

    Grade - AIFSQN

  • IFSQN Associate
  • 49 posts
  • 4 thanks
3
Neutral

  • United States
    United States
  • Gender:Male
  • Location:Chicago, IL
  • Interests:HACCP, HARPC, SQF Practitioner, FSMA, Food Safety Culture, Reading, Creative Writing, Guitars, Piano, Music, Art, Wanderlust, Traveling.

Posted 31 January 2017 - 08:43 PM

Everyone, thanks for the responses.  The comments here and the alternative thread have really helped us drive a new knife safety program...it was MUCH needed!





Share this


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users