Jump to content

  • Quick Navigation
Photo

Water testing corrective actions

Share this

  • You cannot start a new topic
  • Please log in to reply
9 replies to this topic
- - - - -

Inverse

    Grade - MIFSQN

  • IFSQN Member
  • 53 posts
  • 4 thanks
2
Neutral

  • United Kingdom
    United Kingdom

Posted 30 October 2017 - 09:57 AM

Hi all,

 

We just received our tap water test result that indicated TVC @22C and TVC @37C above 300 cfu/100ml (Coliforms & E.coli= 0 cfu/ml). This water is used for cleaning only.

What would be our corrective action in this case? Do we need to clean our tap (if yes, how do we do that??) ? I was trying to find some information but no luck. I'm a bit lost, so any kind of help is much appreciated!

 

Thank you in advance!



Thanked by 1 Member:

Peaches

    Grade - MIFSQN

  • IFSQN Member
  • 134 posts
  • 123 thanks
15
Good

  • United States
    United States
  • Gender:Female

Posted 30 October 2017 - 10:54 AM

Hello

Did you try retesting the same spot and verifying that the water was not contaminated when the sample was taken?  That could be your first corrective action.  If the count still remains high, do you have a main source where the water comes into the facility that you can test?  If the main source sample is within specification, then you need to understand the flow of the water through the pipes (map it out), and if additional samples can be taken along that route (sometimes a water tap can be installed for minimal amount of money by your maintenance department).  That way you can possibly narrow down where the contamination is coming from potentially.  UV lights can also help if nothing else does.  Hope that helps



Thanked by 1 Member:

Inverse

    Grade - MIFSQN

  • IFSQN Member
  • 53 posts
  • 4 thanks
2
Neutral

  • United Kingdom
    United Kingdom

Posted 30 October 2017 - 11:11 AM

Hi Peaches,

 

Thank you for a quick reply.

I'm just about to collect another sample and send it off to our lab.

I'm just wondering if I should stop our production in the meantime or is it not a major hazard, since we use that water for cleaning only? Since I don't have a team, I need to figure out everything myself, so don't want to go overboard in this case...

 

Thank you!



Thanked by 1 Member:

Peaches

    Grade - MIFSQN

  • IFSQN Member
  • 134 posts
  • 123 thanks
15
Good

  • United States
    United States
  • Gender:Female

Posted 30 October 2017 - 11:25 AM

I'm not sure what type of products you produce (high risk/low risk, etc) Do you take any swabs or ATP type swabs that verify the surface is clean besides a visual inspection?  



Thanked by 1 Member:

Inverse

    Grade - MIFSQN

  • IFSQN Member
  • 53 posts
  • 4 thanks
2
Neutral

  • United Kingdom
    United Kingdom

Posted 30 October 2017 - 12:00 PM

We produce dried products (low risk) and routinely do ATP swabs which are usually clear, so that's why I'm a bit confused. We test our water on annual basis and it usually comes out clear. I'll wait for other results and try to figure out where this contamination came from.

 

Thank you :) 



Thanked by 1 Member:

Charles.C

    Grade - FIFSQN

  • IFSQN Moderator
  • 20,542 posts
  • 5662 thanks
1,544
Excellent

  • Earth
    Earth
  • Gender:Male
  • Interests:SF
    TV
    Movies

Posted 30 October 2017 - 07:55 PM

Hi all,

 

We just received our tap water test result that indicated TVC @22C and TVC @37C above 300 cfu/100ml (Coliforms & E.coli= 0 cfu/ml). This water is used for cleaning only.

What would be our corrective action in this case? Do we need to clean our tap (if yes, how do we do that??) ? I was trying to find some information but no luck. I'm a bit lost, so any kind of help is much appreciated!

 

Thank you in advance!

 

Hi Inverse,

 

i assume yr intended specs are as per EC limits.

 

Not sure if you have perhaps confused the EC requirements or simply mis-typed yr own data, ie compare -

 

Attached File  water micro spec.pdf   41.39KB   127 downloads

 

One routine test is as to whether there is a detectable free chlorine level in the water.


Kind Regards,

 

Charles.C


Thanked by 1 Member:

sqflady

    Grade - SIFSQN

  • IFSQN Senior
  • 250 posts
  • 63 thanks
37
Excellent

  • United States
    United States
  • Gender:Female
  • Location:Wisconsin

Posted 31 October 2017 - 12:08 PM

This might be a silly thought but did you remove the aerator that is typically on the tap?  Also, did you ensure a sanitary sample?  When I took many water samples in my previous job, I used a blowtorch to ensure the outlet itself was clean.  You have to remove the aerator because they are plastic and will melt.  This solved many of my positive samples.



Thanked by 1 Member:

Inverse

    Grade - MIFSQN

  • IFSQN Member
  • 53 posts
  • 4 thanks
2
Neutral

  • United Kingdom
    United Kingdom

Posted 31 October 2017 - 02:43 PM

Charles,

 

Thank you for that. I will definitely need to do more research.

 

 

sqflady,

 

Thank you, I haven't thought about it. I will have a look at our outlets and wait for the next result. 



Charles.C

    Grade - FIFSQN

  • IFSQN Moderator
  • 20,542 posts
  • 5662 thanks
1,544
Excellent

  • Earth
    Earth
  • Gender:Male
  • Interests:SF
    TV
    Movies

Posted 02 November 2017 - 05:50 AM

Charles,

 

Thank you for that. I will definitely need to do more research.

 

 

sqflady,

 

Thank you, I haven't thought about it. I will have a look at our outlets and wait for the next result. 

 

Hi Inverse,

 

Yr data may be perfectly acceptable as is with respect to limits. But maybe less so operationally if data shows a significant deviation from yr established baseline.

If there is a positive residual free chlorine, IMEX, the plate counts /ml are typically very low assuming that residence times are adequate.


Kind Regards,

 

Charles.C


Thanked by 1 Member:

Irishlass105

    Grade - MIFSQN

  • IFSQN Member
  • 58 posts
  • 14 thanks
4
Neutral

  • United Kingdom
    United Kingdom

Posted 02 November 2017 - 10:23 AM

I had issues like this with water sampling and done the following;

 

  • UV light added after mains tank area
  • flame sample point 
  • run sample point water for 5/10 mins to ensure water sample taken is representative of water in the tank.

 

Good luck.



Thanked by 2 Members:


Share this

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users