Jump to content

  • Quick Navigation
Photo

Installing third barrier pest control in animal feedmill

Share this

  • You cannot start a new topic
  • Please log in to reply
10 replies to this topic
- - - - -

Shazlin88

    Grade - Active

  • IFSQN Active
  • 23 posts
  • 1 thanks
0
Neutral

  • Malaysia
    Malaysia

Posted 17 April 2019 - 06:36 AM

May I know, is there any alternative besides glue board for third barrier pest control?
Glue board is cannot be used since the dust from raw material in feedmill will affect the glueboard.

Thanks.



tamdongnai

    Grade - Active

  • IFSQN Active
  • 13 posts
  • 0 thanks
0
Neutral

  • Vietnam
    Vietnam

Posted 17 April 2019 - 07:48 AM

Dear Shazlin88

Installing third barrier pest control: by trapper tunnel or plastic dust cover



Shazlin88

    Grade - Active

  • IFSQN Active
  • 23 posts
  • 1 thanks
0
Neutral

  • Malaysia
    Malaysia

Posted 17 April 2019 - 08:58 AM

Dear Shazlin88

Installing third barrier pest control: by trapper tunnel or plastic dust cover

Plastic dust cover? what do you mean? is there any glue below the plastic?



EagleEye

    Grade - MIFSQN

  • IFSQN Member
  • 111 posts
  • 30 thanks
19
Good

  • Earth
    Earth
  • Gender:Male

Posted 17 April 2019 - 11:49 AM

Hi there,

 

What are your target pests?



SQFconsultant

    SQFconsultant

  • IFSQN Fellow
  • 4,629 posts
  • 1135 thanks
1,125
Excellent

  • United States
    United States
  • Gender:Male
  • Interests:Just when I thought I was out - They pulled me back in!!!

Posted 17 April 2019 - 11:58 AM

For rats and mice you could install your glue boards under a 1/2 moon cover, thus preventing dust from settling onto the boards - rats and mice run thru and BAM,done!


All the Best,

 

All Rights Reserved,

Without Prejudice,

Glenn Oster.

Glenn Oster Consulting, LLC -

SQF System Development | Internal Auditor Training | eConsultant

 

 

Martha's Vineyard Island, MA - Restored Republic

http://www.GCEMVI.XYZ

http://www.GlennOster.com

 

774.563.7048


Scampi

    Fellow

  • IFSQN Fellow
  • 5,444 posts
  • 1507 thanks
1,523
Excellent

  • Canada
    Canada
  • Gender:Not Telling

Posted 17 April 2019 - 12:23 PM

Tin cats all the way

http://www.victorpes...ouse-trap-m310s

 

If you're talking about outside, they really should be bait stations and not traps IMO


Please stop referring to me as Sir/sirs


Shazlin88

    Grade - Active

  • IFSQN Active
  • 23 posts
  • 1 thanks
0
Neutral

  • Malaysia
    Malaysia

Posted 17 April 2019 - 12:27 PM

Hi there,
 
What are your target pests?


My target pest is rodent in this case.


Shazlin88

    Grade - Active

  • IFSQN Active
  • 23 posts
  • 1 thanks
0
Neutral

  • Malaysia
    Malaysia

Posted 17 April 2019 - 12:29 PM

Tin cats all the way
http://www.victorpes...ouse-trap-m310s
 
If you're talking about outside, they really should be bait stations and not traps IMO


No-no.. the third barrier is inside the buildings.


pmrinze

    Grade - Active

  • IFSQN Active
  • 1 posts
  • 0 thanks
0
Neutral

  • Guatemala
    Guatemala

Posted 17 April 2019 - 08:10 PM

Use mechanical trap, for example
JT EATON =JAWS
CATCHMASTER = EZ-SET

Inside a station

Regards

Pablo


Enviado desde mi iPad utilizando Tapatalk



MsMars

    Grade - PIFSQN

  • IFSQN Principal
  • 606 posts
  • 194 thanks
151
Excellent

  • United States
    United States
  • Gender:Female

Posted 17 April 2019 - 08:24 PM

IME dust gets absolutely everywhere inside the mill, so glue traps are pretty much useless, even with covers.  Agree with other posts - "tin cats" or other traps are best. 



Marcowilson12

    Grade - Active

  • IFSQN Active
  • 4 posts
  • 0 thanks
0
Neutral

  • Australia
    Australia

Posted 31 May 2019 - 07:50 AM

My target pest is rodent in this case.

 

 

 

 

Hello there,

 

Your target rodent but I thing your take a pest control service but the better company you're check. Otherwise rodent control, mice control. rat control, etc. services need you can contact pest control Sydney company & get the information.





Share this

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users