Jump to content

  • Quick Navigation
Photo

Can you use galvanised steel for gantries and platforms?

Share this

  • You cannot start a new topic
  • Please log in to reply
7 replies to this topic
- - - - -

AggieD

    Grade - Active

  • IFSQN Active
  • 4 posts
  • 2 thanks
0
Neutral

  • United Kingdom
    United Kingdom

Posted 03 March 2022 - 08:57 AM

Hello

I work for a small fresh herbs factory and we are looking to rearrange our prouction areas, and looking at purchasing some new gantries/platforms.

 

My question is, do you know if we could use galvanised steel instead of stainless steel for them?

 

Thank you.

 

 

Aggie


Edited by AggieD, 03 March 2022 - 08:57 AM.


Brendan Triplett

    Grade - PIFSQN

  • IFSQN Principal
  • 511 posts
  • 131 thanks
106
Excellent

  • United States
    United States
  • Gender:Male
  • Interests:Rugby, Military History, Reading

Posted 03 March 2022 - 10:32 AM

I do not see an issue with using the galv. steel in your gantries and platforms as long as you have a check in place to ensure that they are corroding or flaking over time.  It sounds as though you are using them more for transport and structural reasons anyway, more so than using them for food contact surfaces.  The galvanized may corrode faster over time once the topcoat layer comes off or if it gets hit or dinged so keep an eye on it so that there is not risk of it dropping in bins during transport or handling.  Hope this helps.  

 

Cheers!


Vice President and SQF Practitioner in Pennsylvania
Brendan Triplett


AggieD

    Grade - Active

  • IFSQN Active
  • 4 posts
  • 2 thanks
0
Neutral

  • United Kingdom
    United Kingdom

Posted 03 March 2022 - 10:52 AM

I do not see an issue with using the galv. steel in your gantries and platforms as long as you have a check in place to ensure that they are corroding or flaking over time.  It sounds as though you are using them more for transport and structural reasons anyway, more so than using them for food contact surfaces.  The galvanized may corrode faster over time once the topcoat layer comes off or if it gets hit or dinged so keep an eye on it so that there is not risk of it dropping in bins during transport or handling.  Hope this helps.  

 

Cheers!

 

Thank you, it is not going to be a food contact item, and it shouldn't be in danger of damage as there will not be any traffic using ppt's of forklifts around, possibly a pallet lift. 

I was just unsure if there was anything in BRC or ISO that mentions galvanised steel, as i could not find any information about it.

 

Thank you.  



Brendan Triplett

    Grade - PIFSQN

  • IFSQN Principal
  • 511 posts
  • 131 thanks
106
Excellent

  • United States
    United States
  • Gender:Male
  • Interests:Rugby, Military History, Reading

Posted 03 March 2022 - 11:01 AM

FDA on our side of the pond is fine with them being used, as long as the product is not a high-acid product  I think your spices will be fine and I think using it wont be an issue,  I would just keep it as a maintenance item on your GMPs.

 

Cheers!


Vice President and SQF Practitioner in Pennsylvania
Brendan Triplett


Scampi

    Fellow

  • IFSQN Fellow
  • 5,444 posts
  • 1507 thanks
1,524
Excellent

  • Canada
    Canada
  • Gender:Not Telling

Posted 03 March 2022 - 05:10 PM

Galvanized isn't near as friendly to humidity OR commercial cleaning agents.

 

Just know that you will not get the longevity that you would from SS


Please stop referring to me as Sir/sirs


pHruit

    Grade - FIFSQN

  • IFSQN Fellow
  • 2,071 posts
  • 849 thanks
536
Excellent

  • United Kingdom
    United Kingdom
  • Gender:Male
  • Interests:Composing/listening to classical music, electronics, mountain biking, science, sarcasm

Posted 03 March 2022 - 07:26 PM

I agree with Scampi.
I've seen galvanised steels used in non-contact applications and usually it's been a misguided attempt at saving money that didn't work in the long run. Whilst the zinc coating is theoretically able to prevent rust, prolonged exposure to moisture/humidity/acids/alkalis will cause issues.

For dry warehousing I wouldn't be too worried, but I'm sceptical about many factory applications.



Hoosiersmoker

    Grade - PIFSQN

  • IFSQN Principal
  • 683 posts
  • 228 thanks
122
Excellent

  • United States
    United States

Posted 10 March 2022 - 01:54 PM

I wouldn't be as concerned with cleaning or reaction to chemicals as I would knowing it was a gantry and the rolling over of a galvanized surface would absolutely cause flaking and separation of the galvanizing from the steel and wear from walking on it or potentially dropping something on it the same. Also knowing the moving section of a gantry would most certainly be above the level of production, there would also certainly be a potential foreign material issue. A SS gantry or platform would not pose this hazard. Also, inspections would always be after the fact. If your inspection shows a chip or flaking of the galvanizing, you would need to go back and inspect everything produced from the last inspection showing no chipping or flaking. I'm not sure a metal detector would see such small flakes? Also, the few dollars today might save you massive dollars tomorrow. I for one would not like to sprinkle galvanizing on my food thinking it's actually Italian Seasoning.



SQFconsultant

    SQFconsultant

  • IFSQN Fellow
  • 4,632 posts
  • 1135 thanks
1,126
Excellent

  • United States
    United States
  • Gender:Male
  • Interests:Just when I thought I was out - They pulled me back in!!!

Posted 11 April 2022 - 03:12 PM

Galvanized is fine. Include its inspection on foreign material program.


All the Best,

 

All Rights Reserved,

Without Prejudice,

Glenn Oster.

Glenn Oster Consulting, LLC -

SQF System Development | Internal Auditor Training | eConsultant

Martha's Vineyard Island, MA - Restored Republic

http://www.GCEMVI.XYZ

http://www.GlennOster.com

 




Share this

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users