Jump to content

  • Quick Navigation
Photo

Calculating least sterilization z value

Share this

  • You cannot start a new topic
  • Please log in to reply
2 replies to this topic
- - - - -

Paul keida

    Grade - Active

  • Newbie
  • 3 posts
  • 0 thanks
0
Neutral

  • United States
    United States

Posted 16 September 2016 - 02:52 PM

i need help determining z values with a temperature change 

i have a client who mfg a salad dressing with a ph of 3.0 and CCP is less than 3.5 

he heats with the current process to 200F and holds for 5 minutes , cools and hot fills at 180F and inverts for 2 minutes 

 

how would Z values compare if he reduces heat to 195F and holds for 1 minute , then hot fills at 180F 

is there software to compare heat treatments to themal death rate to maintain 5 log reduction ?

thx

 

 



Charles.C

    Grade - FIFSQN

  • IFSQN Moderator
  • 20,542 posts
  • 5662 thanks
1,544
Excellent

  • Earth
    Earth
  • Gender:Male
  • Interests:SF
    TV
    Movies

Posted 17 September 2016 - 02:53 AM

i need help determining z values with a temperature change 

i have a client who mfg a salad dressing with a ph of 3.0 and CCP is less than 3.5 

he heats with the current process to 200F and holds for 5 minutes , cools and hot fills at 180F and inverts for 2 minutes 

 

how would Z values compare if he reduces heat to 195F and holds for 1 minute , then hot fills at 180F 

is there software to compare heat treatments to themal death rate to maintain 5 log reduction ?

thx

 

Hi Paul,

 

Not really my area but I deduce from IT that -

 

"salad dressing" may be FDA regarded as an acid food rather than an acidified one.

 

The crude  F(T,z) lethality values for each stage (assumed to refer constant, coldest temp. point ) can be calculated as per analogous formula to that in this attachment -

 

Attached File  Lethality calculation.doc   79.5KB   125 downloads

 

Strictly you will need appropriate z-value.

The "121"/z values should, i think, preferably be referenced to a level close to yr pasteurizing temperature (eg.90degC). Maybe can try z= 10 for both temps in degC just to get an idea. Then add the 2 stages together.

 

Conservatively, could calculate for 1st stage only, eg ca. (5).[10 ^((93.3-90)/10)] = 10.7 for 1st option. Similarly > 1.12 for 2nd option.

 

And yes, excel programs for F are available and posted on this forum (somewhere). Particularly developed for temperatures not constant.

 

The above calculation compares yr applied F values.

 

Afaik the Z value itself  is based on the applied lethality achieving a typical 5log bacterial reduction of species XYZ so may/may not be satisfied by the F values above.

 

This "validation" step requires a further calculation to determine No.of log reductions of XYZ achieved.

(In practice, i believe  Z- "least sterilization values" may have additional safety factors built in also).

 

So the final step probably requires your specifying a relevant XYZ species, eg L.monocytogenes, determining (searching for) its appropriate D (Decimal Reduction) value for the food matrix involved, and applying one more calculation.

 

PS - this ref. contains  recommended heat processing time/temperature combinations for a 5-log reduction in bacterial pathogens for acidified products with a pH of 4.1 or below -

 

Attached File  Thermal processing of acidified foods, 2010.pdf   154.51KB   139 downloads

 

An additional table was issued in a Draft FDA document (2010) -

 

Attached File  Thermal Process Lethalities for Safe Acidified Foods,2010.doc   47.5KB   108 downloads


Kind Regards,

 

Charles.C


Thanked by 1 Member:
chu lin

Charles.C

    Grade - FIFSQN

  • IFSQN Moderator
  • 20,542 posts
  • 5662 thanks
1,544
Excellent

  • Earth
    Earth
  • Gender:Male
  • Interests:SF
    TV
    Movies

Posted 26 September 2016 - 12:42 PM

addendum JFI

 

Hi Paul,

 

I noticed later that yr actual thread title was seeking "least sterilizing value" (LSV). This might have additional  expectations as compared to my interpretation of the queries in OP as seeking a lethality value based on a specific pathogen.

 

As I understand, LSV (as related to filing forms for "scheduled processes")  can have a rather complicated interpretation and typically seems to be usually reserved for a Process Authority's enumeration. For example see this 2015 thread -

 

http://www.ifsqn.com...water-activity/

 

I have since seen some further indication that the LSV value does relate to an assessment including both terms (a,b) within the practical context of ensuring "commercial sterility" however i have been unable  to determine whether a particular microbial species is routinely used for the additional "b" requirement or if it varies depending on the product. The latter seems more logical.

 

PS - further info. -

 

the F0 (lowest sterilizing value) of the process which results in a commercially sterile product. An F0 of 3.0 minutes is required to achieve a 12 log reduction of Clostridium botulinum1. A higher F0 is required to prevent the growth of non-pathogenic thermophilic spoilage organisms. The F0 is the single value of the lowest sterilizing value achieved by the process.

 

1It is internationally accepted that a minimum sterilizing value of 3.0 minutes is required to render a low-acid canned food microbiologically safe (Huss H. H et al., 2003)

[ref. Huss, H.H; Ababouch, L; Gram, L. (2003) Assessment and Management of Seafood Safety and Quality. Clostridium botulinum Fisheries Technical Paper. No. 444. Rome, Clostridium botulinum]

 

Attached File  Lowest Sterilizing Value,Least Sterilization Value,LSV,CFIA.pdf   375.95KB   125 downloads


Kind Regards,

 

Charles.C


Thanked by 1 Member:
chu lin


Share this

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users