8 replies to this topic

[FSQAManager2025]

Good morning! This is going to sound dumb, but I'd rather ask a dumb question than try to assume something on my own. When it comes to interpreting test results, what are the limits? My facility receives our E. coli results using ECC (cfu / cm²) for the result. Most of the time it is less than <0.03. Last week it was .6. What is considered a failure? What is the limit for this? I was told by my predecessor that the limit is 1,000,000, but this seems like an extremely high number. I'd just like to verify. Thank you! 

[kconf]

It depends on some things. Is this an env sample you are talking about or food sample?

 

What is the nature of food? Raw/finished/produce? What type?

 

If you are being reported <0.03 it is most likely MPN, not CFU. CFU is usually a whole number. Maybe your lab changed the method this time. I'd ask them directly. 

 

The limit is what you set based on what it is and your process. I've seen millions of colonies (coli) on raw meat shelf life. It is not unusual. 

[BigGaz1982]

Limits are based very much on the product, and it's intended use.

 

The Health Protection Agency have released guidelines which can be useful when determining limits. This can be found here

 

Also, the limits of detection from our provider come into play too.

 

For example, a result of <0.03 could mean that the limit of detection is 0.03 for your provider, and therefore it is not detected. If the lab has changed or outsourced, then the 0.6 could also be the limit of detection.

 

Usually the cert would also state "Not Detected" too, but you can clarify that with the provider.

 

If the limit of detection (LoD) is 0.03, and this time the result has come as 0.6, then this would potentially indicate that E.Coli has been detected.

 

Also, the limit for E.Coli is generally "Not Detected". Any result which shows the presence of E.Coli would be a failure. The risk then comes down to the type of foodstuff and thus the source of the E.Coli. But any E.Coli detection would be a failure.

Edited by BigGaz1982, Today, 04:26 PM.

[GMO]

How can a limit of detection be anything but a whole number or less than a whole number? If there are dilution effects then it might be <10 or <20 but <0.03 makes no sense to me.

But I'm not a micro expert.

I'm assuming a swab is meant as it's per cm2. 

[kconf]

I think - not a limit of detection, the result itself recorded as <0.03 is what the OP means. 

[BigGaz1982]

I think - not a limit of detection, the result itself recorded as <0.03 is what the OP means. 

<0.03 would indicate that the lowest the lab is able to quantifiably detected is 0.03. Anything lower than this, they cannot detect. So, as far as they are concerned it is Not Present, but they cannot confirm with absolute certainty that the level of E.Coli is zero due to the accuracy of their tests.

 

In the instance of a result reading <0.03 this would be considered a successful sample. If the same lab is used and records a level of 0.6, then this is a confirmation that there IS E.Coli present and they can actively determine the exact level in the test sample.

[FSQAManager2025]

It is a generic e. coli sample. A sponge used on a carcass, specifically raw beef. 

It depends on some things. Is this an env sample you are talking about or food sample?

 

What is the nature of food? Raw/finished/produce? What type?

 

If you are being reported <0.03 it is most likely MPN, not CFU. CFU is usually a whole number. Maybe your lab changed the method this time. I'd ask them directly. 

 

The limit is what you set based on what it is and your process. I've seen millions of colonies (coli) on raw meat shelf life. It is not unusual. 

[kconf]

Oh I see. Then there is a special calculation for carcass. When doing Pre and Post, pres could be that high. 

[FSQAManager2025]

Your link is for 'ready-to-eat' foods placed on the market. My facilities products are raw beef. Would this still apply? 

Limits are based very much on the product, and it's intended use.

 

The Health Protection Agency have released guidelines which can be useful when determining limits. This can be found here

 

Also, the limits of detection from our provider come into play too.

 

For example, a result of <0.03 could mean that the limit of detection is 0.03 for your provider, and therefore it is not detected. If the lab has changed or outsourced, then the 0.6 could also be the limit of detection.

 

Usually the cert would also state "Not Detected" too, but you can clarify that with the provider.

 

If the limit of detection (LoD) is 0.03, and this time the result has come as 0.6, then this would potentially indicate that E.Coli has been detected.

 

Also, the limit for E.Coli is generally "Not Detected". Any result which shows the presence of E.Coli would be a failure. The risk then comes down to the type of foodstuff and thus the source of the E.Coli. But any E.Coli detection would be a failure.