Jump to content

  • Quick Navigation
Photo

Fabric HVAC ducts in a food production facility?

Share this

  • You cannot start a new topic
  • Please log in to reply
7 replies to this topic
- - - - -

itayuri

    Grade - Active

  • IFSQN Active
  • 10 posts
  • 0 thanks
0
Neutral

  • Israel
    Israel

Posted 06 November 2022 - 12:50 PM

Hi all,

 

Does anyone have any experience with fabric air ducts in a food production facility?

We are looking at it as an option but not sure what are the pros and cons (cost is obviously a pro).

We are mostly concerned about placing such a duct in o of the areas in the facility that needs to be very clean.

I'd love to hear any good / bad experiences you may have had.

 

Thanks,

 

Itay



Scampi

    Fellow

  • IFSQN Fellow
  • 5,444 posts
  • 1507 thanks
1,524
Excellent

  • Canada
    Canada
  • Gender:Not Telling

Posted 07 November 2022 - 02:15 PM

Wil they be exposed to production?


Please stop referring to me as Sir/sirs


itayuri

    Grade - Active

  • IFSQN Active
  • 10 posts
  • 0 thanks
0
Neutral

  • Israel
    Israel

Posted 08 November 2022 - 09:50 AM

Yes,
they will be in the production area.

Sent from my KB2003 using Tapatalk



Scotty_SQF

    Grade - SIFSQN

  • IFSQN Senior
  • 366 posts
  • 87 thanks
139
Excellent

  • United States
    United States
  • Gender:Male
  • Interests:hiking, gravel biking, exploring the great outdoors

Posted 08 November 2022 - 11:57 AM

Not Food, but had them in a place where we did packaging once.  We had to take them down once a year and wash them, as they seemed to have slight mold growth on them.  Especially true in the summer when cold air was running through them creating condensation and with the fabric gave the opportunity for mold to grow.  Luckily, they were not in an area where any converting was happening.  It was just in a hallway and storage areas for printing plates that were covered.  I did not care for them much as the SQF Practitioner. 



Scampi

    Fellow

  • IFSQN Fellow
  • 5,444 posts
  • 1507 thanks
1,524
Excellent

  • Canada
    Canada
  • Gender:Not Telling

Posted 08 November 2022 - 03:22 PM

You're required to have the area made of material that is designed to withstand repeated cleaning--fabric does not fall into that category

 

On top of which, you will have put a harborage point inside your production area

 

Dust and debris will build up on the fabric and fall onto/into your products

 

I wouldn't use them, no money saved in the long run


  • G M likes this

Please stop referring to me as Sir/sirs


Setanta

    Grade - FIFSQN

  • IFSQN Fellow
  • 1,599 posts
  • 369 thanks
383
Excellent

  • United States
    United States
  • Gender:Female
  • Interests:Reading: historical fiction, fantasy, Sci-Fi
    Movies
    Gardening
    Birding

Posted 08 November 2022 - 05:30 PM

Based on what you've said, I agree with Scampi. Should be impervious .


-Setanta         

 

 

 


jfrey123

    Grade - PIFSQN

  • IFSQN Principal
  • 601 posts
  • 173 thanks
293
Excellent

  • United States
    United States
  • Gender:Male
  • Location:Sparks, NV

Posted 08 November 2022 - 07:27 PM

Agree with above, ducts should be impervious and cleanable.  Fabric ducting would allow dust to accumulate and be difficult to remove, and creates a drop hazard for production below.



itayuri

    Grade - Active

  • IFSQN Active
  • 10 posts
  • 0 thanks
0
Neutral

  • Israel
    Israel

Posted 11 November 2022 - 02:36 PM

Thanks everyone for your input.
You confirmed my thoughts on the subject.

Sent from my KB2003 using Tapatalk





Share this

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users