Hello Everyone
We just installed water purification system in our plant. So nobody knows how it operates, can anyone help with the SOP.
Posted 05 May 2014 - 01:27 PM
Hello Everyone
We just installed water purification system in our plant. So nobody knows how it operates, can anyone help with the SOP.
Regards
Ruhama Thooko
Quality Assurance Coordinator
Highlands Trout (Pty) Ltd
Jehova Jire
Posted 05 May 2014 - 03:29 PM
Hello Ruhama Thooko,
what is your source of water from borewell,municipality or river or any other source,
Normally water passes through sand filter than activated carbon filter then through 5,10 micron filters and through Reverse osmoisis (R.O) plant and then finally U.V. light treated and depending upon end usage ozonised.
Edited by SUSHIL, 05 May 2014 - 03:29 PM.
Posted 05 May 2014 - 05:00 PM
Hello Everyone
We just installed water purification system in our plant. So nobody knows how it operates, can anyone help with the SOP.
I assume you do have a list of the components and a diagram of the assembled system. Maybe post this for starters.
I'm quite impressed that you managed to install it on yr own, or was that by a contractor who has now "fled the scene"?
If not, they, or the supplier, would be the logical first step for most people.
Rgds / Charles.C
Kind Regards,
Charles.C
Posted 06 May 2014 - 09:40 AM
Hello Ruhama Thooko,
what is your source of water from borewell,municipality or river or any other source,
Normally water passes through sand filter than activated carbon filter then through 5,10 micron filters and through Reverse osmoisis (R.O) plant and then finally U.V. light treated and depending upon end usage ozonised.
Hey Sushil
We get water from municipality so we found not clean that's why we installed purification system. The components of this system is as you mention.
Regards
Ruhama Thooko
Quality Assurance Coordinator
Highlands Trout (Pty) Ltd
Jehova Jire
Posted 06 May 2014 - 09:44 AM
I assume you do have a list of the components and a diagram of the assembled system. Maybe post this for starters.
I'm quite impressed that you managed to install it on yr own, or was that by a contractor who has now "fled the scene"?
If not, they, or the supplier, would be the logical first step for most people.
Rgds / Charles.C
Hey Charles
Our Maintenance Department installed this by following the manual. So the challenge um facing is about the dosage, That's why I want to document the operating procedure.
Regards
Ruhama Thooko
Quality Assurance Coordinator
Highlands Trout (Pty) Ltd
Jehova Jire
Posted 06 May 2014 - 10:43 AM
Hey Charles
Our Maintenance Department installed this by following the manual. So the challenge um facing is about the dosage, That's why I want to document the operating procedure.
Similar queries.
eg dosage of what ? to achieve what ? passed through what ? injected how ? residence time how long ?
eg something like this objective ? -
microbiologically acceptable output water for plant use (re coliforms/E.coli/TPC) using NaOCl injection after a column filtration system and input water of 'good' micro.quality
If not, how not ?
Rgds / Charles.C
Kind Regards,
Charles.C
Posted 06 May 2014 - 12:31 PM
Hello Ruhama,
You have to first check the Quality of your Municipality water,by giving it to outside accreditated Lab for potability,if you dont have your in-house lab.
Then give your final sample to lab to check the difference of parameters.(Physical,chemical and Microbiological parameters for potable water).
You can dose the municipality water in reservoir (tank) with sodium hypochlorite so that the final chlorine in the water is 2-3 ppm of residual chlorine.
This chlorine will get removed by activated carbon during filteration.You have to daily clean the sand/carbon filter by reverse dosing of water to remove impurities collected as per daily usage,before start of production.
Ozonation (0.3-0.4ppm ozone) is possible if you are bottling water and cannot be used if you are using water for beverages /processing.
Posted 17 May 2014 - 06:27 PM
great job ruh
0 members, 1 guests, 0 anonymous users