Jump to content

  • Quick Navigation
Photo

SQF 11.7.3.9 - Control of Foreign Matter Contamination

Share this

  • You cannot start a new topic
  • Please log in to reply
7 replies to this topic

Julz

    Grade - AIFSQN

  • IFSQN Associate
  • 38 posts
  • 5 thanks
0
Neutral

  • Australia
    Australia

Posted 16 February 2023 - 04:53 AM

Hi,

I would like to ask how others implement the following SQF requirement:

11.7.3.9 Gaskets, rubber impellers, and other equipment made of materials that can wear or deteriorate over time shall be inspected on a regular frequency.

 

We have a mono pump used in our process and I am wanting to know how others inspect the pump for preventative maintenance, in particular the stator, gaskets and seals.  Is a full physical break down of the pump necessary?  Also what frequency do you conduct the inspection?

Thanking you in advance.



AJL

    Grade - SIFSQN

  • IFSQN Senior
  • 336 posts
  • 21 thanks
38
Excellent

  • Germany
    Germany
  • Gender:Male

Posted 16 February 2023 - 08:55 AM

They should go into your preventative maintenance schedule.
The job- card should be either 'inspection' of 'xy' gasket or 'gaskets on 'xy' machine.
You should also set a timeframe for changing them.
When it comes to pumps, no one opens a pump unless they really really have to, so the gaskets and seals just get changed when you do preventative maintenance on the pump (2 x a year or yearly, depending on the usage, risk assessment etc). Usually the maintenance department decide the frequency based on their experience with the pump. They will tend to set the timeframe for as long as they possibly can 😉 from my experience.
Have you got any process filters after the pump? Just curious.
Does that help? 🙂


Edited by AJL, 16 February 2023 - 09:02 AM.


kfromNE

    Grade - FIFSQN

  • IFSQN Fellow
  • 1,054 posts
  • 292 thanks
304
Excellent

  • United States
    United States
  • Gender:Female
  • Interests:Bicycling, reading, nutrition, trivia

Posted 16 February 2023 - 12:39 PM

We use preventative maintenance or pre-op to inspect depending on the item.



Julz

    Grade - AIFSQN

  • IFSQN Associate
  • 38 posts
  • 5 thanks
0
Neutral

  • Australia
    Australia

Posted 16 February 2023 - 10:56 PM

They should go into your preventative maintenance schedule.
The job- card should be either 'inspection' of 'xy' gasket or 'gaskets on 'xy' machine.
You should also set a timeframe for changing them.
When it comes to pumps, no one opens a pump unless they really really have to, so the gaskets and seals just get changed when you do preventative maintenance on the pump (2 x a year or yearly, depending on the usage, risk assessment etc). Usually the maintenance department decide the frequency based on their experience with the pump. They will tend to set the timeframe for as long as they possibly can 😉 from my experience.
Have you got any process filters after the pump? Just curious.
Does that help? 🙂

Thanks AJL, yes we do have a filter post the pump.

The issue is that this production line is only used maximum 2 -3 times a month, so the pump has little wear.  We have only had one issue with it in the 10 years that I have been here.  Also the pump is not easily dismantled.  In saying that, without inspection we will not know if or when the stator is going to fail.  



AJL

    Grade - SIFSQN

  • IFSQN Senior
  • 336 posts
  • 21 thanks
38
Excellent

  • Germany
    Germany
  • Gender:Male

Posted 16 February 2023 - 11:07 PM

Hmmm the maintenance frequency should reflect the number of hours it runs for. 😊=Risk based. I am not an engineer but I would recommend at least yearly anyway, it gets dismantled and inspected. But good luck negotiating that with your maintenance department 🙈
I have a focus on microbiology too and if things like pumps don't get inspected and taken apart often enough they can pose a risk.
In terms of compliance, you need to have your maintenance team ready to defend their risk based frequency of inspection.
You can say that the filter is your verification to a degree- it should catch worn gaskets and (gasp) metal if the pump gets worn and grinds on itself (can happen ,😪)



Thanked by 1 Member:

Tony-C

    Grade - FIFSQN

  • IFSQN Fellow
  • 4,223 posts
  • 1288 thanks
608
Excellent

  • United Kingdom
    United Kingdom
  • Gender:Male
  • Location:World
  • Interests:My main interests are sports particularly football, pool, scuba diving, skiing and ten pin bowling.

Posted 17 February 2023 - 04:20 AM

Hi Julz,

 

To add to previous posts, the manufacturer of the pump should be providing guidelines/instructions for inspection and maintenance.

 

Kind regards,

 

Tony



Thanked by 1 Member:

AJL

    Grade - SIFSQN

  • IFSQN Senior
  • 336 posts
  • 21 thanks
38
Excellent

  • Germany
    Germany
  • Gender:Male

Posted 17 February 2023 - 08:27 AM

Yes great point Tony. 😊
With some of the older equipment it isn't always easy to dig up manuals and guidance but yes that's the best place to go to- then compliance wise you can refer to the manufacturers instructions.
We have some newer equipment so it shows on the screen after a certain amount of hours that the pump needs a service. 😅



SHQuality

    Grade - SIFSQN

  • IFSQN Senior
  • 317 posts
  • 46 thanks
59
Excellent

  • Netherlands
    Netherlands

Posted 17 February 2023 - 01:02 PM

Unless the manual or manufacturer says otherwise, I would open up the machine completely at least once a year, especially when there are components that are not easily accessible that might need replacing or maintaining.

 

I would push for twice a year. If there is a lack of information, you need to collect data to see how long it takes to wear out without running into issues when it happens sooner than expected.


  • AJL likes this



Share this


Also tagged with one or more of these keywords: SQF, Maintenance, 11.7.3.9, Foreign Matter, contamination

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users